John Deere 660 Integral Disk Harrow Operator Manual OMP63178
$30
- Type Of Manual: Operator Manual
- Manual ID: OMP63178
- Format: PDF
- Size: 1.4MB
- Number of Pages: 64
Description
-
Model List:
- 660 Integral Disk Harrow
- 1. Contents
- 1.0.1. Recognize Safety Information
- 1.0.2. Understand Signal Words
- 1.0.3. Follow Safety Instructions
- 1.0.4. Prepare for Emergencies
- 1.0.5. Wear Protective Clothing
- 1.0.6. Practice Safe Maintenance
- 1.0.7. Remove Paint Before Welding or Heating
- 1.0.8. Avoid Heating Near Pressurized Fluid Lines
- 1.0.9. Avoid HighPressure Fluids
- 1.0.10. Keep Riders Off Machine
- 1.0.11. Use Safety Lights and Devices
- 1.0.12. Use Seat Belt Properly
- 1.0.13. Tow Loads Safely
- 1.0.14. Observe Maximum Transport Speed
- 1.1. Safety Signs
- 1.1.1. Read Safety Signs Carefully
- 1.2. Preparing the Tractor
- 1.2.1. Tractor Size
- 1.2.2. Tire Pressure
- 1.2.3. Rockshaft Control Lever
- 1.2.4. Drawbar
- 1.2.5. Rear Wheel Weighting Front end Weighting
- 1.2.6. Stabilizing Chains
- 1.2.7. Adjusting Sway Blocks
- 1.2.8. Adjusting Lateral Float
- 1.2.9. Adjusting Rockshaft SpeedofDrop
- 1.3. Preparing the Machine
- 1.3.1. Verification of the Harrow Disk
- 1.3.2. Hardware
- 1.3.3. Lubrication
- 1.3.4. Familiarize with all Controls of the Harrow Disk and Tractor
- 1.4. Operating the Machine
- 1.4.1. Scrapers Disks
- 1.4.2. Harrow Disk Adjust
- 1.4.3. Filling Furrows
- 1.4.4. The Sections Angle
- 1.4.5. Adjust Front Section Angle
- 1.4.6. Factors that Affect in the Selection of the Angle of the Gangs Disk
- 1.5. Attaching and Detaching
- 1.5.1. Attaching Disk Harrow toTractor
- 1.5.2. Length of the Lift Link Connections
- 1.5.3. Detaching from Tractor
- 1.6. Transporting Machine
- 1.6.1. Use a Safety Chain
- 1.6.2. Use Safety Lights and Devices
- 1.6.3. Tow Loads Safely
- 1.6.4. Observe Maximum Transport Speed
- 1.6.5. Transporting Machine
- 1.7. Attachments
- 1.7.1. Bearing Wear Guard
- 1.7.2. Gang Wrenches
- 1.7.3. Scrapers
- 1.8. Assembly
- 1.8.1. Assembly
- 1.8.2. Disks Sections
- 1.8.3. Tighten Gang Bolts
- 1.8.4. Gang Nut Wrenches
- 1.8.5. Tighten Gang Bolts
- 1.8.6. Standard Ubolt tightening sequence
- 1.8.7. Tightening scraper angle bolt nuts
- 1.8.8. Disks Sections
- 1.8.9. Scrapers
- 1.8.10. Bearings Wear Guard
- 1.9. Troubleshooting
- 1.9.1. Troubleshooting
- 1.10. Lubrication and Maintenance
- 1.10.1. Lubrication Symbols
- 1.10.2. Lubricate the Bearings of the Sections
- 1.11. Service and Adjustments
- 1.11.1. Unified Inch Bolt and Screw Torque Values
- 1.11.2. Metric Bolt and Screw Torque Values
- 1.11.3. Replacing Scrapers
- 1.11.4. Disassembling Disk Gangs
- 1.11.5. Gang Identification
- 1.11.6. Asembling Disk Spools
- 1.11.7. Assembling Sleeve and Bearings
- 1.11.8. Position of the Grease Fitting in the Flange
- 1.11.9. Gang Nut Wrenches
- 1.11.10. Tighten Gang Bolts
- 1.11.11. Identifying Disk Blades Eligible for Warranty
- 1.11.12. Identifying Disk Blades not Eligible for Warranty
- 1.12. Storage
- 1.12.1. Store Attachments Safely
- 1.12.2. Storage
- 1.12.3. Beginning of Season Service
- 1.13. Specifications
- 1.13.1. Tractors Rating Recommendations
- 1.13.2. Main Frame
- 1.13.3. Disks Measurement
- 1.13.4. Product Identification Number
- 1.14. John Deere Service Keeps You On Job
- 1.14.1. John Deere Is At Your Service
- 1.14.2. John Deere Parts
- 1.14.3. The Right Tools
- 1.14.4. WellTrained Technicians
- 1.14.5. Prompt Service
- 2. Page Number
- 2.1. Section 05
- 2.2. Section 10
- 2.3. Section 15
- 2.4. Section 20
- 2.5. Section 25
- 2.6. Section 30
- 2.7. Section 35
- 2.8. Section 40
- 2.9. Section 45
- 2.10. Section 50
- 2.11. Section 55
- 2.12. Section 60
- 2.13. Section 65
- 2.14. Section 70
Related products
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
