John Deere 725D, 730D, 735D, and 740D Draper Platforms Operator Manual OMHXE128001-1

John Deere 725D, 730D, 735D, and 740D Draper Platforms Operator Manual OMHXE128001-2

John Deere 725D, 730D, 735D, and 740D Draper Platforms Operator Manual OMHXE128001-3

John Deere 725D, 730D, 735D, 740D Draper Platforms Operator Manual OMHXE128001

Type Of Manual: Operator Manual
Manual ID: OMHXE128001
Format: PDF
Size: 8.4MB
Number of Pages: 120

Category: John Deere Operators Manuals PDF Tag: Agricultural

Description

Model List:
- 725D Draper Platform
- 730D Draper Platform
- 735D Draper Platform
- 740D Draper Platform

1. Introduction
1.1. Foreword
1.2. A Message to Our Customers
1.3. Identification View
2. Safety Features
2.1. Header Safety Features
2.2. Recognize Safety Information
2.3. Understand Signal Words
2.4. Follow Safety Instructions
2.5. Spanish Safety Signs and Operators Manual
2.6. Ballasting for Safe Ground Contact
2.7. Parking and Leaving the Machine
2.8. Prepare for Emergencies
2.9. Wear Protective Clothing
2.10. Stay Clear of Platform
2.11. Keep Hands Away From Knives
2.12. Use Safety Lights and Devices
2.13. Transport Safely
2.14. Observe Maximum Transport Speed
2.15. Road Transport Disconnect Switch
2.16. Practice Safe Maintenance
2.17. Remove Paint Before Welding or Heating
2.18. Avoid Heating Near Pressurized Fluid Lines
2.19. Avoid Contact With Moving Parts
2.20. Avoid Contact With Cutterbar
2.21. Stay Clear of Rotating Drivelines
2.22. Guards and Shields
2.23. Avoid HighPressure Fluids
2.24. Service Accumulator Systems Safely
2.25. Service Machines Safely
2.26. Service Drive Belts Safely
2.27. Protect Against High Pressure Spray
2.28. Service Tires Safely
2.29. Decommissioning Proper Recycling and Disposal of Fluids and Components
2.30. Support Machine Properly
2.31. Store Attachments Safely
3. Safety Signs
3.1. Front View Decals
3.2. Rear LeftHand View Decals
3.3. Rear LeftCenter View Decals
3.4. Rear LeftCenter View Decals Continued
3.5. Rear LeftCenter View Decals Continued
3.6. Rear RightHand View Decals
3.7. Side View Decals
3.8. Side View Decals Continued
3.9. Replace Safety Signs
4. Transporting
4.1. Transporting on Trailer
4.2. Transporting on Combine
4.3. Converting Transport System for Transport (If Equipped with Slow Speed Integral Transport System)
4.4. Converting Transport System for Field Operation (If Equipped with Slow Speed Integral Transport System)
5. Attaching and Detaching
5.1. Attaching Platform to Combine
5.2. Detaching Platform from Combine
6. Calibration and Settings
6.1. When to Calibrate
6.2. Calibration Error Codes
6.3. Calibration Procedures
6.4. Adjusting Feeder House Drop Rate and Sensitivity
7. Operating the Platform
7.1. General Information
7.2. Armrest Functions
7.3. Active Header Control DisplayFeatures
7.4. Description of Automatic Header Height Control Systems
7.5. Draper Belt Speed
7.6. Draper Belt Speed Adjust Switch (If Equipped)
7.7. Side Belt Speed Reduction Switch
7.8. Cutterbar Tilt Adjust Switch (If Equipped)
7.9. Reel Settings
7.10. Active Header Height Control
7.10.1. Header Height Sensing Adjustment, OffGround
7.11. Dual Zone Float
7.11.1. Features
7.11.2. Controls
7.12. Recommended Combine Settings
7.13. Feed Drum Settings
7.14. Recommended Initial Crop Settings
7.15. Harvesting in Dry Crop Conditions
7.16. Harvesting in Tough Feeding Crop Conditions
7.17. Harvesting in Short, Thin Crops
7.18. Harvesting in Down Crops
7.19. Bushy or High Volume Crops
7.20. Sorghum
8. Attachments and Options
8.1. Slow Speed Integral Transport System
8.2. Top Crop Conveying Auger
8.3. Plastic Skid Shoes
8.4. Crop Lifters
8.5. Crop Lifter Adjustments
8.6. Reel FlipOver Assembly
8.7. Reel End Fingers
8.8. Feed Drum AntiWrap Brackets Combine
8.9. Spare Knife Storage
8.10. Center Feed Section Seal Kit
9. Adjustments
9.1. Suspension and Leveling
9.1.1. Leveling Draper Cutterbar to Ground
9.1.2. Lock and Unlock the Float System
9.1.3. Equalize the Float System
9.1.4. Lock and Unlock Gauge Wheels
9.2. Feed Drum Finger Timing
9.3. Feeding Adjustments
9.3.1. Side Draper Belt Tension
9.3.2. Center Draper Belt Tension
9.4. Knife HoldDown Clearance
9.5. Adjust Center Knife Guards (Dual Knife Cutterbar Machines Only)
9.6. Windrow Conversion
9.6.1. Removing Attachment Frame and Center Feed Assembly
9.6.2. Removing Center Feed Assembly from Attachment Frame
9.6.3. Installing Center Feed Assembly to Attachment Frame
9.6.4. Installing Attachment Frame
9.6.5. Installing Attachment Frame with Center Feed Assembly
9.6.6. Setting Windrow Opening
10. AdjustmentsReel
10.1. Set Reel Safety Stops
10.2. Minimum Reel Height and Leveling Reel
10.3. Fore/Aft Cylinder Mount Adjustment (Single Reel Platform)
10.4. Fore/Aft Cylinder Mount Adjustment (Split Reel Platforms)
10.5. Rephasing Reel Fore/Aft Cylinders
10.6. Rephasing Reel Lift Cylinders
10.7. Bleeding Reel Lift Cylinder System
10.8. Adjust Reel Fingers
10.9. DialASpeed Reel
10.10. Reel Speed Ratio Sensor Adjustment
10.11. Reel Drive Gear Adjustment
11. Lubrication
11.1. Lubricant Storage
11.2. Alternative and Synthetic Lubricants
11.3. Mixing of Lubricants
12. Lubrication and Maintenance
12.1. Care and Maintenance of Belts
12.2. Lubrication Interval Chart
12.3. Every 50 Hours of Operation
12.4. Every 200 Hours of Operation
12.5. Every 400 Hours of Operation
13. Service
13.1. Hydraulic Cylinder Safety Stop
13.1.1. Manual Feeder House Fore/Aft Tilt
13.1.2. Hydraulic Feeder House Fore/Aft Tilt
13.2. Tire Pressure and Wheel Bolt Torque
13.3. Accumulator Pressure
13.4. Set Reel Safety Stops
13.5. Open Side Shields
13.6. Remove and Install Side Shields
13.7. Remove and Install Backshaft Drive Belts
13.8. Remove and Install Telescoping Knife Drive Shaft
13.9. Cutterbar Maintenance
13.10. Knife Section Service Kit
13.11. Remove and Install Cutterbar Knife
13.12. Remove and Install Knife Sections
13.13. Align Knife Head and Knife Drive
13.14. Spare Knife Storage
13.15. Remove and Install Knife Guards
13.16. Center Draper Cleanout Combine
13.17. Cleaning Material Build Up at Side Shields
13.18. Remove and Install Side Draper Belts
13.19. Remove and Install Center Draper Belt Combine
13.20. Remove and Install Feed Drum Finger Guides Combine
13.21. Remove and Install Feed Drum Fingers Combine
13.22. Header Warning Light Bulb Replacement
13.23. Remove and Install Sump Cover Combine
14. Troubleshooting
14.1. Cutting Platform
14.2. Active Header Height Control
15. Storage
15.1. End of Season Service
15.2. Beginning of Season Service
16. Specifications
16.1. Overall Dimensions
16.2. Gauge Wheel Tire Pressure and Wheel Bolt Torque
16.3. Specifications
16.4. Platform Weights
16.5. Keep Machines Secure
16.6. Header Identification Number
16.7. Keep Proof of Ownership
16.8. Unified Inch Bolt and Screw Torque Values
16.9. Metric Bolt and Screw Torque Values
17. John Deere Service Literature Available
17.1. Technical Information
18. John Deere Service Keeps You On The Job
18.1. John Deere Is At Your Service

John Deere 725D, 730D, 735D, 740D Draper Platforms Operator Manual OMHXE128001

Description

Related products

Login