John Deere H480 Loader Operator Manual OMPXX11167

John Deere H480 Loader Operator Manual OMPXX11167-2

John Deere H480 Loader Operator Manual OMPXX11167-3

John Deere H480 Loader Operator Manual OMPXX11167

Type Of Manual: Operator Manual
Manual ID: OMPXX11167
Format: PDF
Size: 4.9MB
Number of Pages: 100

Category: John Deere Operators Manuals PDF Tag: Agricultural

Description

Model List:
- H480 Loader

1. Introduction
1.1. Foreword
2. General Information
2.1. Machine Overview
2.2. Product View
2.3. Trademarks
2.4. Abbreviations
2.5. Regions and Country Versions
2.6. Dealers Record
2.7. Predelivery
2.8. Delivery
2.9. AfterSale
2.10. Recognize Safety Information
2.11. Understand Signal Words
2.12. Follow Safety Instructions
2.13. Prepare for Emergencies
2.14. Wear Protective Clothing
2.15. Park Machine Safely
2.16. Protect People and Animals
2.17. Operating the Loader Tractor Safely
2.18. Use Seat Belt Properly
2.19. Use Foldable ROPS and Seat Belt Properly
2.20. Use Caution on Slopes, Uneven Terrain, and Rough Ground
2.21. Avoid Injury or Death from Falling Loads
2.22. Carry Materials Safely
2.23. Transporting Round Bales Safely
2.24. Operate Grapple (If Equipped)
2.24.1. Avoid Injury or Death from Falling Round Bales
2.24.2. How to Pick Up a Round Bale
2.24.3. How to Pick Up a Round Bale on a Slope
2.24.4. How to Transport a Round Bale
2.24.5. How to Remove Material from a Pile
2.25. Driving on Public Roads
2.26. Operating Loader with Attachments from Other Manufacturers
2.27. Operate Bucket/Attachment Safely
2.28. Operating NonSelfLevelling Loaders
2.29. Avoid Power Lines
2.30. Dig Safely
2.31. Detach Loader Safely
2.32. Use Safety Lights and Devices
2.33. Practice Safe Maintenance
2.34. Service Loader Safely
2.35. Service Machines Safely
2.36. Service Accumulator Systems Safely
2.37. Avoid Heating Near Pressurized Fluid Lines
2.38. Check Hoses for Damage
2.39. Avoid HighPressure Fluids
2.40. Remove Paint Before Welding or Heating
2.41. Decommissioning Proper Recycling and Disposal of Fluids and Components
3. Safety Signs
3.1. Pictorial Safety Signs
3.2. Replace Safety Signs
3.3. Avoid HighPressure Spray on Safety Decals
3.4. Ballast Box
3.5. Accumulator
4. Application Charts
4.1. Approved Tractors
4.2. Approved Front Tires, Load Index, Maximum Turn Angle, and Tread Setting
5. Prepare Tractor
5.1. Prepare the Tractor
5.2. Rear Ballast
5.3. Minimum Rear Ballast Requirements and Tire Ratings
5.4. Remove Front Weights and Weight Support
5.5. Front Tread Setting
5.6. Rear Tread Settings
5.7. Adjust Tractor Flow Rate and Timed Detent
5.7.1. Adjust Flow Rate on 7000 and 8000 Series Tractors
5.7.2. Adjust Timed Detent on 7000 and 8000 Series Tractors
5.7.3. Adjust Flow Rate and Timed Detent on 7R MY1113 and 8R MY1013 Series Tractors
5.7.4. Adjust Flow Rate and Timed Detent on 7R MY14 and 8R MY14 Series Tractors
6. Controls
6.1. Operate Loader with MultiFunction Lever (All Except 7020, 7030, 8030, 7R, and 8R Series Tractors)
6.2. Enable MultiFunction Lever (7020, 7030, and 8030 Series Tractors)
6.3. Disable MultiFunction Lever (7020, 7030, and 8030 Series Tractors)
6.4. Operate Loader with MultiFunction Lever (7020, 7030, and 8030 Series Tractors)
6.5. Enable or Disable MultiFunction Lever (7R MY1113 and 8R MY1013 Series Tractors)
6.6. Operate Loader with MultiFunction Lever (7R MY1113 and 8R MY1013 Series Tractors)
6.7. Operate Loader with MultiFunction Lever (7R MY14 and 8R MY14 Series Tractors)
6.7.1. MultiFunction Lever Controls Custom Setup
6.8. Navigate to Controls Setup (7R MY14 and 8R MY14 Series Tractors)
6.9. Controls Setup (7R MY14 and 8R MY14 Series Tractors)
6.10. Controls (7R MY14 and 8R MY14 Series Tractors)
6.11. Lock Out Control Levers
6.12. Operate Loader with a Selective Control Valve (SCV) with a Finger Pad Control (8000, 8010, 8020, 8030 and 8R Series Tractors)
6.13. Operate Attachment (If Equipped)
6.14. Relieve Hydraulic Pressure
7. Attach and Detach Loader
7.1. Attach Loader
7.2. Detach Loader
8. Attach and Detach Bucket or Attachment
8.1. Attachments Available
8.2. Attach Bucket or Attachment
8.3. Detach Bucket or Attachment
9. Transport
9.1. Keep Riders Off Machine
9.2. Driving on Public Roads
9.3. Carry Loads
10. Operate Loader
10.1. Raise and Lower Loader
10.2. Remove Material from a Pile
10.3. Level Bucket
10.4. Level and Scrape Forward
10.5. Level in Reverse
10.6. Dump Bucket
10.7. Operate Grapple (If Equipped)
10.7.1. Avoid Injury or Death from Falling Round Bales
10.7.2. How to Pick Up a Round Bale
10.7.3. How to Pick Up a Round Bale on a Slope
10.7.4. How to Transport a Round Bale
10.7.5. How to Remove Material from a Pile
10.8. Park Tractor with Loader Attached
11. Lubrication and Maintenance
11.1. Lubricate and Maintain Loader Safely
11.2. Perform Lubrication and Maintenance
11.3. Observe Lubrication Symbols
11.4. Multipurpose Extreme Pressure (EP) Grease
11.5. Alternative and Synthetic Lubricants
11.6. First 3 and 10 Hours
11.6.1. First 3 Hours
11.6.2. First 10 Hours
11.7. Every 10 Hours
11.7.1. Latch Pins
11.7.2. Grapple
11.8. Every 50 Hours
11.8.1. Tighten Mounting Frame Hardware
11.8.2. Tighten MFWD Axle Housing and Kingpin Mounting Hardware
11.9. Every 100 Hours or MonthlyCheck Hydraulic Hoses
11.10. Every Six YearsReplace Hydraulic Hoses
12. Troubleshoot
12.1. Hydraulic
12.2. Mast Pin
13. Service
13.1. Service Loader and/or Tractor Safely (Loader Attached)
13.2. Work in Clean Area
13.3. Avoid HighPressure Fluids
13.4. ORing Installation
13.5. Tighten Hydraulic Fittings and Hoses
13.6. Replace Hydraulic Hoses, Couplers, Tubing, and Connectors
13.7. PlugIn Type Hydraulic Fittings
13.8. Access Front of Tractor8020, 8030, 7R, and 8R Series Tractors
13.9. Access Front of Tractor8000, 8010, 7020, and 7030 Series Tractors
13.10. Identify Hose ConnectionsLoadertoMulticoupler
13.11. Identify Hose Connections7020, 7030, and 7R Series Tractors
13.12. Identify Hose Connections for Finger Pad Control (SCV) Operated Loader8000, 8010, 8020, 8030, and 8R Series Tractors
13.13. Identify Hose Connections for MultiFunction Lever Operated Loader8030 and 8R Series Tractors
13.14. Identify Hose Connections for MultiFunction Lever Operated Loader8000, 8010, and 8020 Series Tractors
13.15. Identify Loader Oil Line Connections
13.16. Metric Bolt and Screw Torque Values
13.17. Unified Inch Bolt and Screw Torque Values
14. Storage
14.1. Prepare Loader for Storage
14.2. Store Loader and Attachments
15. Specifications
15.1. Specification Parameters
15.2. Loader Specifications on 8225R, 8235R, 8245R, 8260R, 8270R, 8285R, 8295R, 8310R, 8320R, 8335R, 8345R, 8360R, 8370R, and 8400R Series with 1300 MFWD Front Axle Tractors
15.3. Loader Specifications on 8225R, 8235R, 8245R, 8260R, 8270R, 8285R, 8295R, 8310R, 8320R, 8335R, 8345R, 8360R, 8370R, and 8400R Series with ILS or 1500 MFWD Front Axle Tractors
15.4. Loader Specifications on 7630, 7730, 7830, and 7930 MFWD Tractors
15.5. Loader Specifications on 7200R, 7210R, 7215R, 7230R, 7250R, 7260R, 7270R, 7280R, 7290R, and 7310R MFWD Tractors
15.6. Round Bale Handling Capacities
15.6.1. Round Bale Capacities
15.6.2. Round Bale Sizes and Weights
16. Serial Number
16.1. Record Product Identification Number
16.2. Keep Proof of Ownership
16.3. Keep Machines Secure
17. CE Approval Specification
17.1. EC Declaration of Conformity
17.2. CE Label
18. John Deere Service Keeps You On The Job
18.1. John Deere Parts
18.2. The Right Tools
18.3. WellTrained Technicians
18.4. Prompt Service

John Deere H480 Loader Operator Manual OMPXX11167

Description

Related products

Login