John Deere L330, L330C, L340, and L340C Large Square Balers Technical Manual TM133219 26APR22

Table of contents
FOREWORD
Section 10 – GENERAL
Group 05 – Safety
Group 10 – Specifications
Group 15 – General Information
Group 20 – Lubrication
Section 20 – DRIVE TRAIN
Group 10 – Diagnosing Malfunctions
Group 15 – Drive Train Protection
Group 20 – Gear Case Repair
Group 30 – Driveline Repair
Section 30 – AUTO GREASE SYSTEM
Group 05 – General Information
Group 10 – Diagnosing Malfunctions
Group 15 – Auto Grease Repair
Group 20 – Divider Blocks
Section 40 – ELECTRICAL SYSTEM
Group 05 – Connector Repair
Group 15 – Electrical Schematics
Group 20 – Tests and Adjustments
Group 25 – Control Units and Power Distribution
Group 30 – ISOBUS Monitor
Group 35 – Wire Harness Routing
Group 40 – Sensors
Section 50 – HYDRAULIC SYSTEM
Group 05 – General Information
Group 10 – Diagnosing Malfunctions
Group 15 – Hydraulic Functional Schematics
Group 20 – Valves, Pumps and Motors
Group 25 – Cylinders
Group 30 – Accumulators
Group 35 – Miscellaneous
Section 60 – PICKUP AND ROTOR
Group 05 – General Information
Group 10 – Diagnosing Malfunctions
Group 15 – Pickup Repair
Group 20 – Rotor Repair
Section 70 – PRECUTTER
Group 05 – General Information
Group 10 – Diagnosing Malfunctions
Group 20 – 3×3 Pickup Precutter
Group 25 – 3×4 Pickup Precutter
Section 80 – FEEDING SYSTEM
Group 05 – General Information
Group 10 – Diagnosing Malfunctions
Group 20 – Adjust Feeding System
Group 25 – Feeding System Repair
Section 90 – BALE CHAMBER
Group 05 – General Information
Group 10 – Diagnosing Malfunctions
Group 15 – Plunger
Group 20 – Tension Panels and Channels
Group 25 – Bale Chamber
Group 30 – Last Bale Ejection
Group 35 – Bale Chute
Section 100 – TYING SYSTEM
Group 05 – General Information
Group 10 – Diagnosing Malfunctions
Group 15 – Knotter Repair
Group 20 – Knotter System Repair
Group 25 – Needle Repair
Group 30 – Replacing Brakes
Group 35 – Knotter Trip Mechanism
Group 40 – Adjusting Knotter
Group 45 – Adjusting Needles
Group 50 – Knotter Fan
Section 110 – BRAKES AND SUSPENSION
Group 05 – General Information
Group 10 – Diagnosing Malfunctions
Group 20 – Hydraulic Brake System
Group 25 – Brake Components
Group 30 – Wheels, Axles, and Steering
Section 120 – BODY REPAIR
Group 10 – Front Shield and Gull Wings Doors
Group 20 – Twine Boxes and Work Platforms
Group 30 – Fiberglass Repair
Section 199 – DEALER FABRICATED TOOLS
Group 05 – Dealer Fabricated Tools
Section 249 – ELECTRICAL COMPONENT INFORMATION
Group 40A – Electrical Assemblies
Group 40B – Sensors
Group 40E – Lights
Group 40F – Fuses
Group 40M – Motors
Group 40X – Interconnects and Ground Points
Group 40Y – Electronically Actuated Mechanical Devices
Section 279 – HYDRAULIC COMPONENT INFORMATION
Group 40A – Accumulator
Group 40B – Sensor or Gauge
Group 40C – Cylinder, Actuator, or Piston
Group 40F – Filter
Group 40G – Valve Block, Assembly, or Gear Case
Group 40H – Cooler
Group 40M – Motor
Group 40O – Orifice
Group 40P – Pump
Group 40R – Reservoir or Tank
Group 40V – Valve
Group 40Y – Solenoid Valve