John Deere SeedStar 2 and SeedStar XP Monitor For 1745 MaxEmerge 5 Planter Operator Manual OMKK54025
$30
- Type Of Manual: Operator Manual
- Manual ID: OMKK54025
- Format: PDF
- Size: 5.5MB
- Number of Pages: 152
Description
-
Model List:
- SeedStar 2 and SeedStar XP Monitor For 1745 MaxEmerge 5 Planter
- 1. Introduction
- 1.1. Foreword
- 1.2. Identification Views
- 1.3. A Message to Our Customers
- 1.4. Preliminary Checks
- 1.5. Regions and Country Versions
- 1.6. Machine Overview
- 1.7. Recognize Safety Information
- 1.8. Understand Signal Words
- 1.9. Follow Safety Instructions
- 1.10. Replace Safety Signs
- 1.11. Prevent Machine Runaway
- 1.12. Avoid HighPressure Fluids
- 1.13. Prevent Battery Explosions
- 1.14. Welding Near Electronic Control Units
- 1.15. Keep Electronic Control Unit Connectors Clean
- 2. Safety Signs
- 2.1. Pictorial Safety Signs
- 2.2. Safety Signs
- 3. How to Use Monitor
- 3.1. Use with GreenStar Monitors
- 3.2. Monitor Controls
- 3.3. Monitor Power up and Power Down
- 3.4. Virtual Terminal Displays
- 3.5. Standard Buttons
- 3.6. Input Entry Methods
- 3.7. Screen Layout Manager
- 3.8. Screen Navigation
- 4. Monitor Settings
- 4.1. Configure Brightness, Volume, and Color
- 4.2. Configure Language and Units of Measure
- 4.3. Configure Date and Time
- 4.4. Touchscreen Calibration
- 5. Performance Monitor
- 5.1. Check Implement Width in Performance Monitor
- 5.2. Radar Configuration
- 5.3. Radar Calibration
- 6. Quick Reference and the Planter Defaults Setup
- 6.1. Quick Reference Setup for Ground Driven Machines
- 6.2. Quick Reference Setup for VRD Machines
- 6.3. Additional Quick Reference Setup for Seedstar XP
- 6.4. The Planter Defaults
- 6.4.1. Vacuum Sensors
- 6.4.2. Down Force Sensors
- 6.4.3. Pneumatic down Force Air Pressure Sensors
- 6.4.4. The Planter at a Glance User Settings
- 6.4.5. Alarms and Limits Setup
- 7. SeedStar 2 SETUP Initial System Configuration
- 7.1. SeedStar 2 System Overview
- 7.2. System Components
- 7.3. Configure Planter Drive Source
- 7.4. Set Meter Type
- 7.5. Configure Frame Layout, Row Layout, and Drive Disconnect Warning
- 7.6. Seed Sensors Onoff
- 7.7. Vacuum Sensor Configuration
- 7.8. Vacuum Sensor Calibration
- 7.9. Pneumatic DownforceAir Pressure Sensor
- 7.10. Calibrate Common Start and Stop Height
- 7.11. Calibrate Separate Start and Stop Height
- 7.12. Ground Speed Source
- 8. SeedStar 2 SETUP Ground Drive
- 8.1. Configure Drive Sections
- 9. SeedStar 2 SETUP VariableRate Drive
- 9.1. VariableRate Drive (VRD) Overview
- 9.1.1. System Components
- 9.1.2. Hydraulic Requirements
- 9.1.3. System Functionality
- 9.1.4. System Performance
- 9.2. Quick Start Overview
- 9.3. Rotate Seed Meters Overview
- 9.4. System Components
- 9.5. Enable VariableRate Drive Software
- 9.6. Configure Planter Drive Sections
- 9.7. Row Unit Drive Type
- 9.8. Adjust Motion Sensor Gap1745
- 9.9. Adjust Parallel Arm Height Switch
- 10. SeedStar 2 SETUP RowCommand
- 10.1. RowCommand Overview
- 10.2. System Components
- 10.3. Configure RowCommand
- 10.4. Recommended RowCommand Section Configurations
- 11. SeedStar XP SETUP Enhanced Monitor System
- 11.1. SeedStar XP Monitoring System Overview
- 11.2. System Components
- 11.3. Ride Dynamics Sensor Configuration
- 11.4. Integrated Pneumatic DownforceAir Pressure Sensor
- 11.5. Downforce Sensor Configuration
- 11.6. Planter at a Glance User Settings
- 11.7. Alarms and Limits Set up Page
- 12. SETUP Seed Rates
- 12.1. Ground Driven MachinesTarget Population and HighLow Warnings
- 12.2. VRD MachinesConfigure Meter, Crop, Disk, and Rates
- 12.3. Population Adjust (PA)
- 13. SeedStar 2 Main Run Screens
- 13.1. Ground Driven Machines
- 13.2. VariableRate Drive Machines
- 13.3. Machines with RowCommand
- 13.4. Setting Single SetPoint Target Downforce
- 13.5. Half Screen Layout
- 13.6. Turning View Warning Suppression
- 13.7. Headland Warning Suppression
- 13.8. Transport Mode
- 14. SeedStar XP Main Run Screens
- 14.1. SeedStar XP Navigation Buttons
- 14.2. Seed Population
- 14.3. Seed Singulation
- 14.4. Seed Spacing Coefficient of Variation
- 14.5. Down Force
- 14.5.1. Single SetPoint Pneumatic Downforce
- 14.6. Ride Dynamics
- 14.7. Row Details
- 14.8. Planter Details
- 14.9. Half Screen Layout
- 15. Counters and Calculators
- 15.1. Area Counters, Seeds Per Hour, Seeds Per Area, and Area Until Empty
- 15.2. Transmission Sprocket Calculator
- 15.3. Seed Estimator by Bag
- 15.4. Seed Estimator by Unit
- 15.5. Seed Estimator by Weight
- 15.6. Vacuum Calculator
- 16. Warning Screens
- 16.1. Turning View Warning Suppression
- 16.2. Warning Messages
- 16.3. Warning Screens for SeedStar 2
- 16.4. Warning Screens for SeedStar 2 (Machines with Single SetPoint Pneumatic Downforce)
- 16.5. Warning Screens for RowCommand
- 16.6. Warning Screens for Variable Rate Drive
- 16.7. Warning Screens for SeedStar XP
- 16.8. Warning Screens for SeedStar XP
- 17. The Seed Tube Sensors
- 17.1. Install and Remove Standard Flush Face Seed Tubes
- 17.2. Install and Remove Optional Seed Tubes
- 17.3. Clean the Seed Tube Sensor
- 18. Attach and Detach Variable Rate Drive
- 18.1. Use Your Tractor and Machine Operator Manuals
- 18.2. Making Proper Hose Connections
- 19. Integrated Pneumatic Downforce
- 19.1. Service Machine Safely
- 19.2. Pneumatic Downforce
- 19.3. Pressurize Pneumatic Downforce System
- 19.4. Depressurize Single Rank Pneumatic Downforce System
- 19.5. Single SetPoint Compressor Relay Location
- 19.6. Electric CompressorRelay and Fuse Location for Power Harness
- 19.7. Clean or Replace Electric Air Compressor Filter
- 19.8. Drain Air Storage Tank
- 20. SeedStar 2 Diagnostics
- 20.1. Controller Hardware, Software, and Part Number Identification
- 20.2. Display Hardware, Software, and Part Number Identification
- 20.3. Sensor Status
- 20.4. System Voltages
- 20.5. Seed Tube Sensor Test
- 20.6. Seed Drop Test
- 20.7. Timed Seed Drop Test
- 20.8. Vacuum Sensor
- 21. SeedStar 2 Diagnostics for RowCommand
- 21.1. EPM Status
- 21.2. Row Clutches
- 21.3. Row Clutches SelfTest
- 22. SeedStar 2 Diagnostics for Variable Rate Drive
- 22.1. Rotate Seed Meters
- 22.2. Variable Rate Drive Component Activity
- 22.3. VRD Event Logs
- 22.4. VRD Motor/Valve Flush
- 23. SeedStar XP Diagnostics
- 23.1. Ride Dynamics Sensor Diagnostics
- 23.2. Down Force Sensor Diagnostics
- 23.3. Diagnostics Code
- 24. Troubleshooting
- 24.1. SeedStar 2 and SeedStar XP Troubleshooting
- 24.2. Troubleshoot GreenStar Display
- 24.3. Troubleshoot SeedStar 2
- 24.4. Troubleshoot Variable Rate Drive
- 24.5. Troubleshoot RowCommand
- 24.6. Troubleshoot SeedStar XP
- 24.7. Troubleshoot Single SetPoint Pneumatic Downforce System
- 25. Storage
- 25.1. Beginning of the Season Service
- 25.2. Vacuum Sensor
- 25.3. Pneumatic Downforce Air Spring Storage Procedures
- 25.3.1. When Storing Machine
- 25.3.2. When Removing Machine from Storage
- 26. Specifications
- 26.1. Record Serial Numbers
Related products
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
