Manitou 200 ATJ ST5 S1, 200 ATJ RC ST5 S1 Operator Manual 647845EN-USM1A032021

Manitou 200 ATJ ST5 S1, 200 ATJ RC ST5 S1 Operator Manual 647845EN-USM1A032021 - Image 2

Manitou 200 ATJ ST5 S1, 200 ATJ RC ST5 S1 Operator Manual 647845EN-USM1A032021 - Image 3

Manitou 200 ATJ ST5 S1, 200 ATJ RC ST5 S1 Operator Manual 647845EN-USM1A032021 - Image 4

manitou 200 atj st5 s1 200 atj rc st5 s1 operator manual 647845en usm1a032021 2

Manitou 200 ATJ ST5 S1, 200 ATJ RC ST5 S1 Operator Manual 647845EN-USM1A032021

Type Of Manual: Operator Manual
Manual ID: 647845EN-USM1A032021
Format: PDF
Size: 10.0MB
Number of Pages: 184

Category: Manitou Operator Manual PDF

Description

Model List:
- 200 ATJ ST5 S1
- 200 ATJ RC ST5 S1

1. OPERATING AND SAFETY INSTRUCTIONS
1.1. INSTRUCTIONS TO THE COMPANY MANAGER
1.1.1. THE SITE
1.1.2. THE OPERATOR
1.1.3. THE MACHINE
1.1.3.1. A SUITABILITY OF THE MACHINE FOR THE TASK
1.1.3.2. B ADAPTING THE MACHINE TO USUAL ENVIRONMENTAL CONDITIONS
1.1.3.3. C MODIFYING THE MACHINE
1.1.4. INSTRUCTIONS
1.1.5. MAINTENANCE
1.2. INSTRUCTIONS FOR THE OPERATOR
1.2.1. INTRODUCTION
1.2.2. GENERAL INSTRUCTIONS
1.2.2.1. A OPERATORS MANUAL
1.2.2.2. B AUTHORISATION FOR USE IN FRANCE
1.2.2.3. C MAINTENANCE
1.2.2.4. D MODIFYING THE MACHINE
1.2.2.5. E GROUND LINK
1.2.2.6. F SAFETY DEVICES
1.2.3. OPERATING INSTRUCTIONS
1.2.3.1. A BEFORE USING THE MACHINE
1.2.3.2. B DRIVERS CAB LAYOUT
1.2.3.3. C ENVIRONMENT
1.2.3.4. D VISIBILITY
1.2.3.5. E STARTING MACHINES WITH A DIESEL ENGINE
1.2.3.6. F SWITCHING ON ELECTRICAL MACHINES
1.2.3.7. G DRIVING THE MACHINE
1.2.3.8. H SHUTTING DOWN THE MACHINE
1.2.4. INSTRUCTIONS FOR WELDING AND BLOW TORCH WORK ON AN EXTERNAL STRUCTURE
1.2.4.1. A WITH AN ELECTRICAL WELDING SET
1.2.4.2. B WITH A BLOW TORCH
1.3. MACHINE MAINTENANCE INSTRUCTIONS
1.3.1. GENERAL INSTRUCTIONS
1.3.2. MAINTENANCE
1.3.2.1. MAINTENANCE LOGBOOK
1.3.3. LUBRICANT AND FUEL LEVELS
1.3.4. HYDRAULICS
1.3.5. ELECTRICITY
1.3.6. TILT SENSOR
1.3.7. WELDING ON THE MACHINE
1.3.8. WASHING THE MACHINE
1.4. IF THE MACHINE IS NOT TO BE USED FOR A LONG TIME
1.4.1. INTRODUCTION
1.4.2. PREPARATION OF THE MACHINE
1.4.3. MACHINES WITH A DIESEL ENGINE ENGINE PROTECTION
1.4.4. ELECTRICAL MACHINES BATTERY CHARGE
1.4.5. PROTECTING THE MACHINE
1.4.6. BRINGING THE MACHINE BACK INTO SERVICE
1.5. DISPOSING OF THE MACHINE
1.5.1. RECYCLING OF MATERIALS
1.5.1.1. METALS
1.5.1.2. PLASTICS
1.5.1.3. RUBBER
1.5.1.4. GLASS
1.5.2. ENVIRONMENTAL PROTECTION
1.5.2.1. WORN OR DAMAGED PARTS
1.5.2.2. USED OIL
1.5.2.3. USED BATTERIES
2. DESCRIPTION
2.1. CE DECLARATION OF CONFORMITY
2.2. COMPONENT LOCATIONS
2.3. STICKERS
2.4. SPECIFICATIONS
2.5. DIMENSIONS AND AMPLITUDE OF MOVEMENT
2.6. SAFETY COMPONENTS
2.6.1. SLIDING MID RAIL
2.6.2. SLIDING MID RAIL AND GATE
2.6.3. SAFETY HARNESS ATTACHMENT POINTS
2.6.4. HANDRAILS
2.6.5. TURNTABLE LOCKING PIN
2.7. CONTROL PANEL AND SAFETY DEVICES AT GROUND LEVEL
2.8. CONTROL PANEL AND SAFETY DEVICES IN THE PLATFORM
2.9. GROUND LEVEL DISPLAY SCREEN
2.9.1. POWERUP CYCLE
2.9.2. DISPLAY ZONES
2.9.3. PREHEAT PAGE
2.9.4. WORK PAGE
2.9.5. ALERT PAGE AND FAULT PAGE
2.10. OPERATING THE MACHINE
2.10.1. TRANSPORT/WORKING POSITION
2.10.1.1. TRANSPORT POSITION
2.10.1.2. WORKING POSITION
2.10.2. OPERATION FROM THE GROUND LEVEL CONTROL PANEL
2.10.2.1. SWITCH ON THE MACHINE
2.10.2.2. SWITCH OFF THE MACHINE
2.10.2.3. START THE DIESEL ENGINE
2.10.2.4. SWITCH OFF THE DIESEL ENGINE
2.10.2.5. POSITION THE PLATFORM
2.10.2.6. ACTIVATE SIMULTANEOUS FUNCTIONS
2.10.2.7. EMERGENCY STOP
2.10.3. USE FROM THE PLATFORM CONTROL PANEL
2.10.3.1. TURN THE MACHINE ON/OFF
2.10.3.2. START THE DIESEL ENGINE
2.10.3.3. SWITCH OFF THE DIESEL ENGINE
2.10.3.4. DRIVE, STEER AND BRAKE THE MACHINE
2.10.3.5. POSITION THE PLATFORM
2.10.3.6. ACTIVATE SIMULTANEOUS FUNCTIONS
2.10.3.7. EMERGENCY STOP
2.10.4. DIESEL ENGINE AUTOMATIC STOP SYSTEM STOP AND GO
2.10.5. AUTOMATIC EXHAUST REGENERATION
2.10.6. STATIONARY MACHINE EXHAUST REGENERATION
2.10.7. LOCKED FUNCTIONS
2.10.7.1. MACHINE IN TRANSPORT POSITION
2.10.7.2. MACHINE IN WORKING POSITION
2.11. EMERGENCY CONTROLS
2.11.1. SHOULD THE USER FEEL ILL PRIORITY CONTROLS FROM THE GROUND
2.11.2. IF THERE IS A BREAKDOWN EMERGENCY CONTROLS FROM THE PLATFORM
2.11.3. IF THERE IS A BREAKDOWN EMERGENCY CONTROLS FROM THE GROUND
2.12. STANDARD EQUIPMENT
2.12.1. OSCILLATING FRONT AXLE
2.13. OPTIONS
2.13.1. KEY LOCK FOR TURNTABLE COVERS
2.13.2. BATTERY CUTOFF
2.13.3. V ELECTRIC POWER SOCKET IN THE PLATFORM
2.13.4. BATTERY HEATER
2.13.5. HYDRAULIC OIL HEATER
2.13.6. ENGINE BLOCK HEATER
2.13.7. ELECTRIC GENERATOR
2.13.8. PLATFORM WORKLIGHT
2.13.9. TURNTABLE SLEWING ALARM
2.13.10. SECONDARY PROTECTION SYSTEM SPS
2.14. TRANSPORT AND LIFTING
2.14.1. TRANSPORT INSTRUCTIONS
2.14.1.1. LOADING/UNLOADING THE MACHINE
2.14.1.2. CONFIGURE THE MACHINE FOR TRANSPORT
2.14.1.3. SECURING THE MACHINE
2.14.2. FREEWHEEL FOR WINCHING
2.14.3. LIFTING INSTRUCTIONS
3. MAINTENANCE
3.1. INTRODUCTION
3.2. ORIGINAL MANITOU SPARE PARTS AND EQUIPMENT
3.3. DAILY AND MONTHLY MAINTENANCE
3.4. MANDATORY SERVICING AND PERIODIC MAINTENANCE
3.5. OCCASIONAL MAINTENANCE AND OCCASIONAL OPERATIONS
3.6. FILTER CARTRIDGES AND BELTS
3.7. LUBRICANTS, COOLANT AND FUEL
3.8. Ü DAILY MAINTENANCE
3.9. Ü MONTHLY MAINTENANCE OR EVERY 50HOURS OF SERVICE
3.10. Ü 250H PERIODIC MAINTENANCE EVERY 250 HOURS OF SERVICE OR 6 MONTHS
3.11. Ü 500H PERIODIC MAINTENANCE EVERY 500 HOURS OF SERVICE OR 1 YEAR
3.12. Ü 1000H PERIODIC MAINTENANCE EVERY 1,000 HOURS OF SERVICE OR 2 YEARS
3.13. Ü 1500H PERIODIC MAINTENANCE EVERY 1,500 HOURS OF SERVICE OR 3 YEARS
3.14. Ü 2000H PERIODIC MAINTENANCE EVERY 2,000 HOURS OF SERVICE OR 4 YEARS
3.15. Ü 3000H PERIODIC MAINTENANCE EVERY 3,000 HOURS OF SERVICE OR 6 YEARS
3.16. Ü OCCASIONAL SERVICING
3.17. Ü OCCASIONAL OPERATIONS

Manitou 200 ATJ ST5 S1, 200 ATJ RC ST5 S1 Operator Manual 647845EN-USM1A032021

Description

Related products

Login