John Deere 615P Belt Pickup Operator Manual OMHXE127789
$30
- Type Of Manual: Operator Manual
- Manual ID: OMHXE127789
- Format: PDF
- Size: 2.8MB
- Number of Pages: 60
Description
-
Model List:
- 615P Belt Pickup
- 1. Introduction
- 1.1. Foreword
- 1.2. A Message to Our Customers
- 1.3. Identification View
- 2. Safety Features
- 2.1. Header Safety Features
- 2.2. Recognize Safety Information
- 2.3. Understand Signal Words
- 2.4. Follow Safety Instructions
- 2.5. Spanish Safety Signs and Operators Manual
- 2.6. Ballasting for Safe Ground Contact
- 2.7. Parking and Leaving the Machine
- 2.8. Prepare for Emergencies
- 2.9. Wear Protective Clothing
- 2.10. Stay Clear of Harvesting Units
- 2.11. Use Safety Lights and Devices
- 2.12. Transport Combine With Header Safely
- 2.13. Road Transport Disconnect Switch
- 2.14. Practice Safe Maintenance
- 2.15. Remove Paint Before Welding or Heating
- 2.16. Avoid Heating Near Pressurized Fluid Lines
- 2.17. Avoid Contact With Moving Parts
- 2.18. Stay Clear of Rotating Drivelines
- 2.19. Guards and Shields
- 2.20. Avoid HighPressure Fluids
- 2.21. Service Accumulator Systems Safely
- 2.22. Service Machines Safely
- 2.23. Service Drive Belts Safely
- 2.24. Protect Against High Pressure Spray
- 2.25. Service Tires Safely
- 2.26. Decommissioning Proper Recycling and Disposal of Fluids and Components
- 2.27. Support Machine Properly
- 2.28. Store Attachments Safely
- 3. Safety Signs
- 3.1. Rear View Decals
- 3.2. Side View Decals
- 3.3. Replace Safety Signs
- 4. Transporting
- 4.1. Transporting on Trailer
- 4.2. Transporting on Combine
- 5. Attaching and Detaching
- 5.1. Rear Auger Stripper Extension Location
- 5.2. Attaching Header to Feeder House
- 5.3. Detaching Header from Feeder House
- 6. Calibration and Settings
- 6.1. When to Calibrate
- 6.2. Before Calibration
- 6.3. Calibration Error Codes
- 6.4. Air Spring Setup (Prior to Header Calibration)
- 6.5. User Calibration Procedures
- 6.6. Adjusting Feeder House Drop Rate and Sensitivity
- 7. Operating the Belt Pickup
- 7.1. Armrest Functions
- 7.2. Active Header Control DisplayFeatures
- 7.3. Description of Automatic Header Height Control Systems
- 7.4. Pickup Speed
- 7.5. Pickup Height
- 7.6. Pickup Pitch
- 7.7. Pickup Pitch (Normal Windrow Condition)
- 7.8. Pickup Pitch (Poor Windrow Condition)
- 7.9. Pickup Pitch (Rocky Conditions)
- 7.10. Adjusting Windrow HoldDown (Wind Screen)
- 7.11. Wet or Muddy Terrain (Light Gauge Wheel Pressure)
- 7.12. Large and Uneven Windrows
- 8. Adjustments Belt Pickup
- 8.1. Service Tires Safely
- 8.2. Adjusting Air Springs
- 8.3. Periodic Checking of Air Spring Pressure
- 8.4. Adjusting Windrow HoldDown (Wind Screen) Fixed Position
- 8.5. Adjusting Auger Position
- 8.6. Adjusting Auger Height
- 8.7. Adjusting Auger Fore/Aft (Left Side)
- 8.8. Adjusting Auger Fore/Aft (Right Side)
- 8.9. Adjusting Finger Timing
- 8.10. Adjusting Rear Stripper
- 8.11. Adjusting Floor Stripper
- 8.12. Adjusting Auger Chain Tension
- 8.13. Adjusting Transfer Belt Tension
- 8.14. Adjusting Picking Belt Tension
- 8.15. Belt Tracking Issues
- 8.15.1. Tracking Issues
- 8.15.2. Belt Drift
- 8.15.3. Correcting Belt Wave From Over Tensioning
- 8.16. Adjusting DialASpeed Belt Speed Ratio
- 8.17. Setting Speed Ratio Sensor
- 9. Lubrication
- 9.1. Lubricant Storage
- 9.2. Alternative and Synthetic Lubricants
- 9.3. Mixing of Lubricants
- 10. Lubrication and Maintenance
- 10.1. Lubrication Symbols
- 10.2. Care and Maintenance of Belts
- 10.3. Lubrication Interval Chart
- 10.4. Every 50 Hours of Operation
- 10.5. Every 200 Hours of Operation
- 11. Service
- 11.1. Hydraulic Cylinder Safety Stop
- 11.1.1. Manual Feeder House Fore/Aft Tilt
- 11.1.2. Hydraulic Feeder House Fore/Aft Tilt
- 11.2. Open Side Shield
- 11.3. Replacing Pickup Belts
- 11.4. Replacing Pickup Fingers
- 11.5. Replacing Auger Fingers and Retainers
- 11.6. Header Warning Light Bulb Replacement
- 11.7. Rephasing Windrow HoldDown Cylinders
- 12. Troubleshooting
- 12.1. Belt Pickup
- 12.2. Active Header Control (AHC)
- 13. Storage
- 13.1. End Of Season Service
- 13.2. Beginning Of Season Service
- 14. Specifications
- 14.1. Specifications
- 14.2. Keep Machines Secure
- 14.3. Header Identification Number
- 14.4. Keep Proof of Ownership
- 14.5. Unified Inch Bolt and Screw Torque Values
- 14.6. Metric Bolt and Screw Torque Values
- 15. John Deere Service Literature Available
- 15.1. Technical Information
- 16. John Deere Service Keeps You On The Job
- 16.1. John Deere Is At Your Service
Related products
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
