John Deere 700X Series Cutting Platform Operator Manual OMHXE152284
$30
- Type Of Manual: Operator Manual
- Manual ID: OMHXE152284
- Format: PDF
- Size: 5.8MB
- Number of Pages: 92
Description
-
Model List:
- 700X Series Cutting Platform
- 1. Introduction
- 1.1. Foreword
- 1.2. Trademarks
- 1.3. A Message to Our Customers
- 1.4. John Deere Technical Information Bookstore
- 1.5. Recognize Safety Information
- 1.6. Follow Safety Instructions
- 1.7. Observe Road Traffic Regulations
- 1.8. Use Safety Lights and Devices
- 1.9. Prepare for Emergencies
- 1.10. Wear Protective Clothing
- 1.11. Store Attachments Safely
- 1.12. Guards and Shields
- 1.13. Stay Clear of Harvesting Units
- 1.14. Keep Hands Away From Knives
- 1.15. Stay Clear of Rotating Drivelines
- 1.16. Stay Clear of Cutterbar When Rotating Auger
- 1.17. Ballasting for Safe Ground Contact
- 1.18. Practice Safe Maintenance
- 1.19. Service Machines Safely
- 1.20. Service Drive Belts Safely
- 1.21. Support Machine Properly
- 1.22. Protect Against Noise
- 1.23. Avoid Heating Near Pressurized Fluid Lines
- 1.24. Avoid HighPressure Fluids
- 1.25. Decommissioning Proper Recycling and Disposal of Fluids and Components
- 1.26. Road Transport Disconnect Button
- 1.27. Replace Safety Signs
- 1.28. Safety Signs
- 2. Field Operation
- 2.1. Cutting PlatformtoCombine Adaptation
- 2.2. Rework the Combine (If Necessary)
- 2.3. Attach Cutting Platform
- 2.4. Adjust Cutting Platform Tilt Angle
- 2.5. Header Height Control Skid Plates
- 2.6. Detach Cutting Platform
- 2.7. Transport Cutting Platform on a Trailer
- 2.8. Cutting Platform Emergency Mode
- 2.9. Calibrate Cutting Platform
- 2.10. Cutterbar and Reel Safety Feature
- 2.11. Cutterbar and Reel Safety FeatureSelf Test
- 2.12. Engage Cutting Platform Drive
- 2.13. Operate the Cutting PlatformGeneral
- 2.13.1. Cutting Platform Controls
- 2.13.2. Cutterbar Position
- 2.13.3. Cutting Height
- 2.13.4. Reel Settings
- 2.13.5. Auger Settings
- 2.14. Operate the Cutting PlatformCrop Condition Adaptation
- 2.15. Composite Reel Tines (Option)
- 2.16. Knife Speed Increase Kit
- 2.17. Fine Knife (Option)
- 2.18. Crop Dividers (Option)
- 2.18.1. Foldable Crop Divider Transport Position
- 2.18.2. Store Crop Dividers (722X Only)
- 2.18.3. Store Crop Dividers (725X740X)
- 2.19. Long Outer Deflector Kit
- 2.20. Rapeseed Knife (Option)
- 2.20.1. Store Rapeseed Knives (722X Only)
- 2.20.2. Store Rapeseed Knives (725X 740X)
- 2.21. Rapeseed Knife Lower Protection (Option)
- 2.22. Lifting Guards (Option)
- 2.22.1. Arrangement of Lifting Guards
- 2.22.2. Adapt Lifting Guards to Ground Conditions
- 2.23. Knife Protection Guard (If Equipped)
- 2.24. Troubleshooting
- 2.24.1. Cutterbar Difficulties
- 2.24.2. Down and Tangled Crops Difficulties
- 2.24.3. Feeder House Difficulties
- 2.24.4. Auger Difficulties
- 2.24.5. Cutting Difficulties
- 2.24.6. Reel Difficulties
- 2.25. Safety Stop for Feeder House Lift Cylinder
- 2.26. Set Safety Stop for Reel Lift Cylinder
- 2.27. Clean Cutterbar Table
- 2.28. Adjust Cutterbar Position
- 2.29. Adjust Reel Tine Pitch
- 2.30. Adjust Reel Support Position
- 2.31. Adjust Auger Height
- 2.32. Adjust Auger Fore/Aft
- 2.33. Adjust Auger Finger Timing
- 2.34. Adjust Rear Stripper
- 2.35. Adjust Floor Stripper
- 3. Lubrication and Maintenance
- 3.1. Required EmissionRelated Information
- 3.1.1. Service Provider
- 3.2. Safety Stop for Feeder House Lift Cylinder
- 3.3. Set Safety Stop for Reel Lift Cylinder
- 3.4. Side Shields
- 3.5. Tool Box (Option)
- 3.6. Gear Oil
- 3.7. Alternative and Synthetic Lubricants
- 3.8. Mixing of Lubricants
- 3.9. Lubricant Storage
- 3.10. Maintenance Interval Chart
- 3.11. Lubrication Chart
- 3.12. Main Drive Gear Case
- 3.13. Knife Drive Gear Case
- 3.14. Auger Drive Slip Clutch
- 3.15. Cutterbar Table Sheet and Sealing Bridge
- 3.16. Header Height Control SensorsOnce a Year
- 3.17. Check Reel Zero Setting
- 3.18. Hydraulic Valve Blocks
- 3.19. Rephase Reel Fore/Aft Cylinders
- 3.20. Rephase Reel Lift Cylinders
- 3.21. Adjust Reel Speed Sensor
- 3.22. Adjust Knife Drive Belt Tension
- 3.23. Replace Knife Drive Belts
- 3.24. Replace Cutterbar Knife
- 3.25. Replace Cutterbar Wear Plates
- 3.26. Set Knife Timing (735X and 740X Only)
- 3.27. Align Knife Head and Knife Drive
- 3.28. Replace Knife Sections
- 3.29. Adjust Auger Drive Chain Tension
- 3.30. Replace Auger Fingers and Retainers
- 3.31. Replace Stubble Light Bulb (NonLight Emitting Diode (LED) LightsIf Equipped)
- 3.32. Replace Stubble Light (Light Emitting Diode (LED) LightsIf Equipped)
- 3.33. End of Season
- 3.34. Beginning of Season Service
- 4. Specifications
- 4.1. 740X Cutting Platforms
- 4.1.1. Cutting Platform
- 4.1.2. Conveyor Auger
- 4.1.3. Slip ClutchTorque
- 4.2. Type Plates
- 4.3. Cutting Platform (Product Identification) Type Plate
- 4.4. Product Identification Number
- 4.5. Machine Component Serial Numbers
- 4.6. Metric Bolt and Screw Torque Values
- 4.7. Unified Inch Bolt and Screw Torque Values
- 4.8. Keep Machines Secure
- 4.9. Keep Proof of Ownership
- 4.10. EC Declaration of Conformity
- 4.11. Eurasian Economic Union
- 4.12. Machine Design Life
- 5. John Deere Service Literature Available
- 5.1. Technical Information
- 6. John Deere Service Keeps You On the Job
- 6.1. John Deere Parts
- 6.2. The Right Tools
- 6.3. WellTrained Technicians
- 6.4. Prompt Service
Related products
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
-50%
Original price was: $20.$10Current price is: $10.
