John Deere 9.0L OEM Diesel Engine (Interim Tier 4 Stage III B Platform) Operator Manual OMRG38038

Contents:
Record Keeping
Record Engine Serial Number
Engine Option Codes
Emission Control Information Label
Record Aftertreatment Serial Numbers
Record High-Pressure Fuel Pump Model and Serial Numbers
Record Rear Power Take-Off (PTO) Serial Number (If Equipped)
Record ECU Serial Number
Safety
Recognize Safety Information
Understand Signal Words
Follow Safety Instructions
Replace Safety Signs
California Proposition 65 Warning
Illuminate Work Area Safely
Work in Clean Area
Use Proper Tools
Live With Safety
Prevent Machine Runaway
Handle Fuel Safely-Avoid Fires
Prepare for Emergencies
Handle Starting Fluid Safely
In Case of Fire
Handle Fluids Safely-Avoid Fires
Avoid Static Electricity Risk When Refueling
Service Machines Safely
Wear Protective Clothing
Protect Against Noise
Handling Batteries Safely
Prevent Acid Burns
Stay Clear of Rotating Drivelines
Install All Guards
Practice Safe Maintenance
Remove Paint Before Welding or Heating
Avoid Heating Near Pressurized Fluid Lines
Avoid High-Pressure Fluids
Do Not Open High-Pressure Fuel System
Protect Against High Pressure Spray
Prevent Battery Explosions
Avoid Hot Exhaust
Exhaust Filter Cleaning
Work In Ventilated Area
Service Cooling System Safely
Decommissioning – Proper Recycling and Disposal of Fluids and Components
Fuels, Lubricants, and Coolants
Diesel Fuel
Supplemental Diesel Fuel Additives
Lubricity of Diesel Fuel
Handling and Storing Diesel Fuel
Biodiesel Fuel
Testing Diesel Fuel
Fuel Filters
Minimizing the Effect of Cold Weather on Diesel Engines
John Deere Break-In Plusâ„¢ Engine Oil – Interim Tier 4, Final Tier 4, Stage IIIB, Stage IV, and Stage V
Diesel Engine Oil – Interim Tier 4, Final Tier 4, Stage IIIB, Stage IV, and Stage V
Diesel Engine Oil and Filter Service Intervals – Interim Tier 4, Final Tier 4, Stage IIIB, Stage IV, and Stage V- OEM Applications
Diesel Engine Oil and Filter Service Intervals
Mixing of Lubricants
Alternative and Synthetic Lubricants
Lubricant Storage
Oil Filters
Diesel Engine Coolant (engine with wet sleeve cylinder liners)
Water Quality for Mixing with Coolant Concentrate
Operating in Warm Temperature Climates
Testing Coolant Freeze Point
Disposing of Coolant
Instrument Panels
PV101 Instrument Panels
PV101 Diagnostic Gauge – Using
PV101 Diagnostic Gauge – Main Menu
PV101 Diagnostic Gauge – Essential Menus
DG14 Diagnostic Gauge – Using
DG14 Diagnostic Gauge – Main Menu
DG14 Diagnostic Gauge – Essential Menus
PV480 Instrument Panel
PV480 Diagnostic Gauge – Using
PV480 Diagnostic Gauge – Main Menu
PV480 Diagnostic Gauge – Essential Menus
Main Menu Navigation
Engine Configuration Data
Accessing Stored Trouble Codes
Accessing Active Trouble Codes
Engine Shutdown Codes
Adjusting Backlighting
Adjusting Contrast
Selecting Units Of Measurement
Setup 1-Up Display
Setup 4-Up Display
John Deere PowerSight
Engine Operation
Break-In Service
Generator Set (Standby) Applications
Starting the Engine
Normal Engine Operation
Cold Weather Operation
Warming Engine
Idling Engine
Changing Engine Speed
Stopping the Engine
Using a Booster Battery or Charger
Auxiliary Gear Drive Limitations
Exhaust Filters
Exhaust Filter Cleaning and Maintenance
Exhaust Filter – Cleaning
Diesel Particulate Filter Maintenance and Service
Exhaust Filter – Diesel Particulate Filter Ash Handling and Disposal
Exhaust Filter – Disposal
Exhaust Filter System Overview
Diagnostic Gauge Keys and Indicators Overview
Passive Regeneration
Automatic (AUTO) Exhaust Filter Cleaning
Manual/Parked Exhaust Filter Cleaning
Disable Exhaust Filter Cleaning
Exhaust Filter Service Required
Lubrication and Maintenance
Required Emission-Related Information
Observe Service Intervals
Use Correct Fuels, Lubricants, and Coolant
Lubrication and Maintenance Service Interval Chart-Standard Industrial Engines
Lubrication and Maintenance Service Interval Chart-Generator (Standby) Applications
Lubrication & Maintenance – Daily
Daily Prestarting Checks
Lubrication & Maintenance – 500 Hours/12 Months
Servicing Fire Extinguisher
Servicing Battery
Changing Engine Oil and Replacing Oil Filter
Visually Inspecting Coolant Pump
Checking Open Crankcase Vent (OCV)
Removing and Installing Fuel Filters
Checking Belt Tensioner Spring Tension and Belt Wear
Checking Belt Wear
Checking Tensioner Spring Tension
Checking Cooling System
Pressure Testing Cooling System
Checking and Adjusting Engine Speeds
Checking Engine Mounts
Checking Engine Ground Connection
Lubrication & Maintenance – 2000 Hours/24 Months
Checking Crankshaft Vibration Damper
Lubrication & Maintenance – 3000 Hours/36 Months
Adjusting Valve Clearance
Lubrication & Maintenance – 6000 Hours/72 Months
Flushing And Refilling Cooling System
Bleeding Air From Cooling System
Testing Thermostat
Service As Required
Additional Service Information
Do Not Modify Fuel System
Drain Water From Fuel Filters
Adding Coolant
Pre-Start Cleaning Guide
Replacing Air Cleaner Filter Elements
Inspecting Primary Filter Element
Cleaning Primary Filter Element
Element Storage
Cleaning the Exhaust Filter
Replacing Fan/Alternator Belt
Checking Fuses
Checking Electrical Wiring And Connections
Bleeding Fuel System
Checking Air Compressors (If Equipped)
Checking Refrigerant (A/C) Compressor (If Equipped)
Checking Rear Power Take-Off (PTO)
Troubleshooting
General Troubleshooting Information
Instrument Panel Method for Retrieving Diagnostic Trouble Codes
Displaying Of Diagnostic Trouble Codes (DTCs)
Listing of Diagnostic Trouble Codes (DTCs)
Intermittent Fault Diagnostics
Displaying Diagnostic Gauge Software
Engine Troubleshooting
Electrical Troubleshooting
Lubrication System Troubleshooting
Cooling System Troubleshooting
Air Intake and Exhaust System Troubleshooting
Precautions for Electrical System When Steam Cleaning Engine
Engine Wiring Harness Layout
Precautions For Welding
Auxiliary Engine Wiring Diagram
Auxiliary Engine Wiring Diagram (Continued)
Auxiliary Engine Wiring Diagram (Continued)
Main Engine Wiring Harness
Main Engine Wiring Harness (continued)
Main Engine Wiring Harness (continued)
Main Engine Wiring Harness (continued)
Control Panel Wiring Harness
Control Panel Wiring Harness (continued)
Control Panel Wiring Harness (continued)
Storage
Engine Storage Guidelines
Preparing Engine for Long Term Storage
Removing Engine from Long Term Storage
Specifications
General OEM Engine Specifications
Engine Power and Speed Rating Specifications 1
Engine Crankcase Oil Fill Quantities
Unified Inch Bolt and Screw Torque Values
Metric Bolt and Screw Torque Values
Lubrication and Maintenance Records
Using Lubrication and Maintenance Records
Daily (Prestarting) Service
500 Hours of Operation/or Every 12 Months Service
2000 Hours of Operation/or Every 24 Months Service
3000 Hours of Operation/or Every 36 Months Service
6000 Hours of Operation/or Every 72 Months Service
Service as Required
Warranty
John Deere Warranty in OEM Applications
Emissions Control System Certification Label
EPA Non-road Emissions Control Warranty Statement-Compression Ignition
CARB Non-road Emissions Control Warranty Statement-Compression Ignition
Service Literature
Technical Information