John Deere 2230 Floating Hitch Field Cultivator Operator Manual OMKK55222-1

John Deere 2230 Floating Hitch Field Cultivator Operator Manual OMKK55222-2

John Deere 2230 Floating Hitch Field Cultivator Operator Manual OMKK55222-3

John Deere 2230 Floating Hitch Field Cultivator Operator Manual OMKK55222

Type Of Manual: Operator Manual
Manual ID: OMKK55222
Format: PDF
Size: 4.6MB
Number of Pages: 108

Category: John Deere Operators Manuals PDF Tag: Agricultural

Description

Model List:
- 2230 Floating Hitch Field Cultivator

1. Introduction
1.1. Foreword
1.2. Recognize Safety Information
1.3. Understand Signal Words
1.4. Follow Safety Instructions
1.5. Spanish Safety Signs and Operators Manual
1.6. Prepare for Emergencies
1.7. Wear Protective Clothing
1.8. Practice Safe Maintenance
1.9. Handle Electronic Components and Brackets Safely
1.10. Support Raised Equipment
1.11. Remove Paint Before Welding or Heating
1.12. Avoid Heating Near Pressurized Fluid Lines
1.13. Avoid HighPressure Fluids
1.14. Check Hydraulic Hoses
1.15. Inspect Lift Circuit Hoses
1.16. Store Attachments Safely
1.17. Service Tires Safely
1.18. Decommissioning Proper Recycling and Disposal of Fluids and Components
1.19. Handle Chemical Products Safely
1.20. Operate Safely
1.21. Use Safety Lights and Devices
1.22. Keep Riders Off Machine
1.23. Observe Maximum Transport Speed
1.24. Use a Signal Person
1.25. Use a Safety Chain
1.26. Tow Loads Safely
1.27. Avoid Overhead Power Lines
1.28. Prepare for Transport
1.29. Transport Safely
1.30. Implements in Train Transport
1.31. Transport Lockup Valve
1.32. Do Not Operate SCV I in Continuous with Wheel Retraction Valve
1.33. Do Not Fold Wings Until Machine Is Fully Raised
1.34. Park Safely
2. Safety Signs
2.1. Replace Damaged or Missing Safety Signs
2.2. Main Frame
2.3. Large 5Section Main Frame
2.4. Section Outer Wing
2.5. Cylinder Locks
2.6. Informational Decals
3. Safety Features
3.1. Safety Features
4. Preparing Tractor
4.1. Use Tractor Operators Manual
4.2. Determine Tractor Requirements
4.3. Drawbar Requirements
4.4. Secure ThreePoint Hitch
4.5. Power TakeOff
4.6. Position Drawbar
4.7. Prepare Hydraulic SystemJohn Deere R/RT Series Tractors
4.8. Use a Safety Chain
5. Preparing Machine
5.1. Drawbar Requirements
5.2. Check and Lubricate Machine
5.3. Check Tire PressureAll Tillage Machines
5.4. Check Wheel HardwareAll Tillage Machines
5.5. Tighten Hardware
5.6. Adjust FronttoRear Level
5.7. Adjust SidetoSide Level
6. Attaching and Detaching
6.1. Use Your Tractor and Tillage Equipment Operators Manuals
6.2. Before Attaching Machine to Tractor
6.3. Attach Machine to Tractor
6.4. Make Proper Hose Connections
6.5. Attach Electrical Connectors
6.6. Position Jack for Transport
6.7. Attach Safety Chain to Tractor
6.8. Engage Transport Lockup Valve
6.9. Check WingFold Operation
6.10. Check Single Point Depth Control
6.11. Raising and Lowering Rear Parking StandMachines With Rear Hitch
6.12. Detach Machine from Tractor
7. Transporting
7.1. Use Safety Lights and Devices
7.2. Observe Maximum Transport Speed
7.3. Use a Safety Chain
7.4. Attach Safety Chain to Tractor
7.5. Tow Loads Safely
7.6. Avoid Overhead Power Lines
7.7. Prepare for Transport
7.8. Close Transport Lockup Valve
7.9. Use Cylinder Locks
7.10. Light Enhancement Module
7.11. Keep Riders Off Machine
7.12. Position Drawbar
7.13. Position Jack for Transport
7.14. Transport Machine
8. Operating Machine
8.1. Keep Riders Off Machine
8.2. Follow Safe Operating Procedures
8.3. Guidelines for Use
8.4. Tighten Hardware
8.5. Use Operators Manual Holder
8.6. Use Adjustment Wrench
8.7. Prepare to Operate Machine in Field
8.8. Adjust Single Point Depth Control
8.9. Level Machine
8.10. Adjust Coil Tine Harrows
8.10.1. Adjust Spring Tension
8.10.2. Adjust Coil Tine Angle
8.11. Adjust Spike Tooth Harrows
8.11.1. Adjust Harrow Height and Draft
8.11.2. Adjust Harrow Spike Angle
8.12. Adjust Rolling Baskets
8.13. Understand Active Hydraulic Rolling Basket DownPressure System
8.14. Adjust Rolling Basket DownPressureTractors With ElectroHydraulic Closed Center Systems
8.15. Operate Optional Rear Hitch
9. Lubrication and Maintenance
9.1. Lubricating and Maintaining Machine Safely
9.2. Multipurpose Extreme Pressure (EP) Grease
9.3. Alternative and Synthetic Lubricants
9.4. Lubricant Storage
9.5. Beginning and End of Season
9.6. Lubrication Symbols
9.7. Lubrication Intervals
9.8. Lubricate Jack
9.9. Lubricate Wheel Bearings
9.10. Lubricate Caster Wheel Pivot Bearings
9.11. Lubricate Fore/Aft Links
9.12. Repack Walking Beam Pivot Bearings
10. Troubleshooting
10.1. Troubleshooting Machine
10.2. Troubleshooting PermaLoc Sweeps
10.3. Troubleshooting Drawbar Hitch Links
10.4. Troubleshoot 5Section Machine WingFold Operation
10.5. Recommendations for Working Hard Soils
10.6. Recommendation for Excessive Harrow Plugging
11. Service
11.1. Practice Safe Maintenance
11.2. Use Safe Service Procedures
11.3. Work in Clean Area
11.4. Service Machines Safely
11.5. Illuminate Work Area Safely
11.6. Support Machine Properly
11.7. Keep Service Area Clean
11.8. Replacing Ground Engaging Tools
11.9. Tighten Hardware
11.10. Metric Bolt and Screw Torque Values
11.11. Unified Inch Bolt and Screw Torque Values
11.12. Face Seal Fittings Assembly and InstallationAll Pressure Applications
11.12.1. Face Seal ORing to Stud End Installation
11.12.2. Face Seal Adjustable Stud End ORing Installation
11.12.3. Face Seal Straight Stud End ORing Installation
11.12.4. Fitting Installation
11.12.5. Assembly Torque
11.13. Metric Face Seal and ORing Stud End Fitting Torque ChartStandard Pressures
11.14. SAE Face Seal and ORing Stud End Fitting Torque ChartStandard Pressures
11.15. Discarded Tires
11.16. Service Tires Safely
11.17. Check Tire PressureAll Tillage Machines
11.18. Repair TireMain Frame
11.19. Check Wheel HardwareAll Tillage Machines
11.20. Service Walking BeamType 1
11.20.1. Disassemble and Inspect Walking Beam
11.20.2. Assemble Walking Beam
11.21. Service Walking BeamType 2
11.21.1. Disassemble and Inspect Walking Beam
11.21.2. Assemble Walking Beam
11.22. Inspect Depth Control Rockshaft Bearings
11.23. Replace Depth Control Bearings
11.24. Check CShank Assembly
11.25. Check Standard Bushings
11.26. Replace SplitTension Bushings
11.27. Replace Worn PermaLoc Sweeps
11.28. Remove PermaLoc Sweeps
11.29. Attach PermaLoc Sweeps
11.30. Attach PermaLoc Casting
11.31. Prevent Hydraulic System Contamination
11.32. Checking Single Point Depth Control for Leakage
11.33. Analyzing Test ResultsSeriesParallel System3Section Machines
11.34. Analyzing Test ResultsSeriesParallel System5Section Machines
11.35. Removing Hydraulic Cylinders
11.36. Before Bleeding Hydraulic System
11.37. Cleanliness
11.38. Bleed Hydraulic System All Machines
11.39. Bleed Optional Rolling Basket Hydraulic Cylinders
11.40. Replace Hydraulic Hoses
11.41. Replace Wheel Retraction Switch5Section Machines ONLY
11.42. Service Rolling Baskets
12. Storage
12.1. Preparing for Storage
12.2. Removing From Storage
13. Specifications
13.1. Hitch Specifications
13.2. Download Force on Tractor Drawbar
13.3. Tractor Power Recommendations
13.4. Machine Specifications
13.5. Tire Specifications
13.6. Standards and Sweeps Specifications
13.7. Hydraulic Hose Specifications
13.8. ProFinish Leveling SystemAttachment Specifications
13.9. Record Product Identification Number (PIN.)
13.10. Keep Proof of Ownership
13.11. Keep Machines Secure
14. John Deere Service Literature Available
14.1. Technical Information
15. John Deere Service Keeps You On The Job
15.1. John Deere Is At Your Service

John Deere 2230 Floating Hitch Field Cultivator Operator Manual OMKK55222

Description

Related products

Login