John Deere DN456 and DN485 Dry Spinner Spreader Operator Manual OMKK39700
John Deere DN456 and DN485 Dry Spinner Spreader Operator Manual OMKK39700-2
John Deere DN456 and DN485 Dry Spinner Spreader Operator Manual OMKK39700-3
John Deere DN456 and DN485 Dry Spinner Spreader Operator Manual OMKK39700-2
John Deere DN456 and DN485 Dry Spinner Spreader Operator Manual OMKK39700-3

John Deere DN456 and DN485 Dry Spinner Spreader Operator Manual OMKK39700

$30

  • Type Of Manual: Operator Manual
  • Manual ID: OMKK39700
  • Format: PDF
  • Size: 5.6MB
  • Number of Pages: 174
Category: Tag:
Description
  • Model List:

    • DN456 Dry Spin Spreader
    • DN485 Dry Spinner Spreader
  • 1. Contents
  • 1.0.1. Recognize Safety Information
  • 1.0.2. Understand Signal Words
  • 1.0.3. Follow Safety Instructions
  • 1.0.4. Prepare for Emergencies
  • 1.0.5. Wear Protective Clothing
  • 1.0.6. Protect Against Noise
  • 1.0.7. Practice Safe Maintenance
  • 1.0.8. Park Machine Safely
  • 1.0.9. Remove Paint Before Welding or Heating
  • 1.0.10. Avoid Heating Near Pressurized Fluid Lines
  • 1.0.11. Avoid HighPressure Fluids
  • 1.0.12. Decommissioning Proper Recycling and Disposal of Fluids and Components
  • 1.0.13. Handle Chemical Products Safely
  • 1.0.14. Service Spreader Equipment Safely
  • 1.0.15. Use Proper Tools
  • 1.0.16. Work In Ventilated Area
  • 1.0.17. Handling Batteries Safely
  • 1.0.18. Service Drive Belts Safely
  • 1.0.19. Using Compressed Air For Cleaning
  • 1.0.20. Maintain a Safety Area Around the Machine
  • 1.0.21. Working Area
  • 1.0.22. Avoid Backover Accidents
  • 1.0.23. Before Operating
  • 1.0.24. Operate Safely
  • 1.0.25. Avoid Injury from Thrown Objects
  • 1.0.26. Use Safety Lights and Devices
  • 1.0.27. Keep Riders Off Machine
  • 1.0.28. Passenger Seat
  • 1.0.29. Use Steps and Handholds Correctly
  • 1.0.30. Use Seat Belt Properly
  • 1.0.31. Use Caution On Hillsides
  • 1.0.32. Transport and Operate Safely
  • 1.0.33. Prevent Machine Runaway
  • 1.0.34. Handle Fuel SafelyAvoid Fires
  • 1.0.35. Handle Agricultural Chemicals Safely
  • 1.0.36. Spreading Dusty Materials
  • 1.0.37. Avoid Exposure To Chemicals
  • 1.0.38. Clean Vehicle of Hazardous Chemicals, Including Pesticides
  • 1.0.39. NonPermissible Use
  • 1.0.40. Emergency Exit
  • 1.1. Safety Signs Location
  • 1.1.1. Replace Safety Signs
  • 1.1.2. Spreader Front Decal
  • 1.1.3. Conveyor Cover Decal
  • 1.1.4. LeftHand Front Decal
  • 1.1.5. LeftHand Front Side Decals
  • 1.1.6. LeftHand Rear Side Decals
  • 1.1.7. LeftHand Spinner Guard Decals
  • 1.1.8. Rear Decal
  • 1.1.9. RightHand Rear Side Decals
  • 1.1.10. RightHand Front Side Decal
  • 1.2. Installation Instructions
  • 1.2.1. Remove Rear Light BarIf Equipped
  • 1.2.2. Install Dry Spreader Body
  • 1.2.3. Attach Harness Connectors
  • 1.2.4. Install Hydraulic Hoses
  • 1.2.5. Hose Installation Guide
  • 1.2.6. Install Beacon Light KitIf Equipped
  • 1.2.7. Install Mirrors and Mirror Brackets
  • 1.2.8. Install Inverted VDN456
  • 1.2.9. Install Inverted VDN485
  • 1.2.10. Install Second Product BinSpreaders with Belt Over Chain Conveyors
  • 1.2.11. Install Second Product BinSpreaders with Straight Belt Conveyors
  • 1.2.12. Install Second Product Bin Hillside Divider
  • 1.2.13. Install Dual Conveyor Cover
  • 1.2.14. Install StarFire Receiver Bracket (EU Exports Only)
  • 1.2.15. Install Speed Limit Decal
  • 1.2.16. Remove Second Product Bin and Install Endgate
  • 1.3. Safety Features
  • 1.3.1. Safety Features
  • 1.4. Dry Application System Application
  • 1.4.1. Access Dry Application System
  • 1.4.2. Dry Application Main Page
  • 1.4.3. Edit Rate Presets
  • 1.4.4. Bin Details
  • 1.4.5. Bin Counter Reset
  • 1.4.6. Prime Controls
  • 1.4.7. Bin Chaining
  • 1.4.8. Bin Purge
  • 1.4.9. Bin and Product Alarms
  • 1.4.10. Target Rate Alarm
  • 1.4.11. Product Density Alarm
  • 1.4.12. Select Spinner Preset
  • 1.4.13. Edit Spinner Preset
  • 1.4.14. Advanced Settings
  • 1.5. Calibrations
  • 1.5.1. Spinner Calibration
  • 1.5.2. Spinner Calibration Procedure
  • 1.5.3. Conveyor Feed Rate Calibration
  • 1.5.4. Conveyor Feed Rate Calibration Procedure
  • 1.5.5. Spreader Check
  • 1.5.6. Spreader Check Procedure
  • 1.5.7. Icons Displayed during Spreader Check Procedure
  • 1.5.8. Rate Control Selection
  • 1.6. PreStarting Checks
  • 1.6.1. Informational Decal
  • 1.6.2. Verify Spinner Orientation
  • 1.6.3. Align Spinner Frame
  • 1.6.4. Verify Material Divider Position
  • 1.6.5. Install Material DeflectorOptional
  • 1.6.6. Verify Spinner Fin Installation
  • 1.6.7. Verify Spinner Speed Sensor Gap
  • 1.6.8. Verify Hillside Divider Location
  • 1.6.9. Verify Correct Chain TensionBelt Over Chain Conveyor Only
  • 1.6.10. Verify Second Product Bin Hillside Divider Location
  • 1.6.11. Verify Correct Belt TensionStraight Belt Conveyor Only
  • 1.6.12. Spinner Initial Adjustment
  • 1.7. Operate System
  • 1.7.1. Initial StartUp
  • 1.7.2. Field Test
  • 1.7.3. Spreader System Check
  • 1.7.4. Setup Display
  • 1.7.5. General Operation Process
  • 1.8. Size Grading and Crush Strength Test
  • 1.8.1. Introduction
  • 1.8.2. Crush Strength
  • 1.8.3. Crush Strength Test
  • 1.8.4. Size Grade Number
  • 1.8.5. Size Grade Number Scale
  • 1.9. Spread Pattern
  • 1.9.1. Spread Pattern Adjustment
  • 1.9.2. Spinners
  • 1.9.3. Spreader Preparation
  • 1.9.4. Determine Material Bulk Density
  • 1.9.5. Determine Material CFR
  • 1.9.6. Calculate Feedgate Opening
  • 1.9.7. Spread Pattern Test Procedure
  • 1.9.8. Analyze Test Results
  • 1.9.9. Driving Methods
  • 1.9.10. Troubleshooting
  • 1.10. Lubrication and Maintenance
  • 1.10.1. Clean Vehicle of Hazardous Chemicals, Including Pesticides
  • 1.10.2. Prevent Hydraulic System Contamination
  • 1.10.3. Dispose of Waste Properly
  • 1.10.4. Service Intervals
  • 1.10.5. Conveyor CleanoutAs Required
  • 1.10.6. Straight Belt Conveyor Maintenance and Adjustment As Required
  • 1.10.7. Belt Over Chain Conveyor Maintenance and AdjustmentAs Required (If Equipped)
  • 1.10.8. Install Replacement Spreader FinsAs Required
  • 1.10.9. Clean Bin SensorAs Required
  • 1.10.10. Lubricate Belt Over Chain ConveyorDaily
  • 1.10.11. Lubricate Idler Shaft Bearings and Adjustment ScrewsWeekly
  • 1.10.12. Lubricate Snubber and Drive Shaft BearingsWeekly
  • 1.10.13. Lubricate Spinner JackWeekly
  • 1.10.14. Lubricate Second Product Bin Drive and Idler Shaft BearingsWeekly
  • 1.10.15. Lubricate Feedgate Jack Tube (If Equipped)Weekly
  • 1.10.16. Check Gear Case OilMonthly
  • 1.10.17. Change Gear Case OilAnnually
  • 1.10.18. Lubricate Feedgate Jack Gears (If Equipped)Annually
  • 1.10.19. Lubricate Second Product Bin Idler Adjustment ScrewsAnnually
  • 1.11. Lubricant Specifications
  • 1.11.1. Hydrostatic/Hydraulic Drive Oil
  • 1.11.2. Gear Case Oil
  • 1.11.3. Chain Oiler Mixture
  • 1.12. Troubleshooting
  • 1.12.1. Troubleshooting
  • 1.12.2. Hydraulic Schematic
  • 1.13. Storage
  • 1.13.1. Avoid Exposure To Chemicals
  • 1.13.2. Clean Vehicle of Hazardous Chemicals, Including Pesticides
  • 1.13.3. Prepare Machine for Storage
  • 1.13.4. Remove Machine from Storage
  • 1.14. Specifications
  • 1.14.1. Specifications DN456
  • 1.14.2. Specifications DN485
  • 1.14.3. Dimensions DN456
  • 1.14.4. Dimensions DN485
  • 1.14.5. Unified Inch Bolt and Screw Torque Values
  • 1.14.6. Metric Bolt and Screw Torque Values
  • 1.14.7. Face Seal Fittings Assembly and InstallationAll Pressure Applications
  • 1.14.8. Metric Face Seal and ORing Stud End Fitting Torque ChartStandard Pressures
  • 1.14.9. Metric Face Seal and ORing Stud End Fitting Torque ChartHigh Pressure Applications
  • 1.14.10. SAE Face Seal and ORing Stud End Fitting Torque ChartStandard Pressures
  • 1.14.11. SAE Face Seal and ORing Stud End Fitting Torque ChartHigh Pressure Applications
  • 1.14.12. Four Bolt Flange Fittings Assembly and InstallationAll Pressure Applications
  • 1.14.13. SAE Four Bolt Flange Cap Screw Torque ValuesStandard Pressure Applications
  • 1.14.14. SAE Four Bolt Flange Cap Screw Torque ValuesHigh Pressure Applications
  • 1.14.15. External Hexagon Port Plug Torque Chart
  • 1.14.16. Speed Limit Decal
  • 1.14.17. Identification Numbers
  • 1.14.18. Interpret the Serial Number of Your Machine 17 digits PIN
  • 1.14.19. Year of Production Table (Digit 5)
  • 1.14.20. Keep Proof of Ownership
  • 1.14.21. Keep Machines Secure
  • 1.15. John Deere Service Keeps You On The Job
  • 1.15.1. John Deere Parts
  • 1.15.2. The Right Tools
  • 1.15.3. WellTrained Technicians
  • 1.15.4. Prompt Service
  • 2. Page Number
  • 2.1. Section 05
  • 2.2. Section 10
  • 2.3. Section 15
  • 2.4. Section 20
  • 2.5. Section 25
  • 2.6. Section 30
  • 2.7. Section 35
  • 2.8. Section 40
  • 2.9. Section 45
  • 2.10. Section 50
  • 2.11. Section 55
  • 2.12. Section 60
  • 2.13. Section 65
  • 2.14. Section 70
  • 2.15. Section 75

Related products

Mahindra Tractor 16 Series 3016 Gear HST Full Parts Manual Fast Download

Mahindra

Mahindra Tractor 16 Series 3016 Gear HST Parts Manual

$20
Add to cart
-50%
Mahindra Tractor 10 Series 3510 4110 Full Operator Manual Fast Download

Mahindra

Mahindra Tractor 10 Series 3510 4110 Operator Manual

Original price was: $20.Current price is: $10.
Add to cart
Mahindra Tractor 16 Series 1816 HST Full Parts Manual Fast Download

Mahindra

Mahindra Tractor 16 Series 1816 HST Parts Manual

$20
Add to cart
Mahindra Tractor 10 Series 5010 HST Cab Full Operator Manual Fast Download

Mahindra

Mahindra Tractor 10 Series 5010 HST Cab Operator Manual

$20
Add to cart
-50%
Mahindra Tractor 30 Series 4WD 4530 Full Operator Manual Fast Download

Mahindra

Mahindra Tractor 30 Series 4WD 4530 Operator Manual

Original price was: $20.Current price is: $10.
Add to cart
Mahindra Tractor 10 Series 4010 HST Full Parts Manual Fast Download

Mahindra

Mahindra Tractor 10 Series 4010 HST Parts Manual

$20
Add to cart
Mahindra Tractor 16 Series 2216 Gear HST Full Parts Manual Fast Download

Mahindra

Mahindra Tractor 16 Series 2216 Gear HST Parts Manual

$20
Add to cart
-50%
Mahindra Tractor 16 Series 3316 Gear HST Full Operator Manual Fast Download

Mahindra

Mahindra Tractor 16 Series 3316 Gear HST Operator Manual

Original price was: $20.Current price is: $10.
Add to cart